U-Boot 1.1.3 (FSL Development) (Feb 21 2007 - 16:24:19) MPC83XX Clock configuration: Coherent System Bus: 266 MHz Core: 533 MHz Local Bus Controller: 266 MHz Local Bus: 66 MHz DDR: 266 MHz I2C: 266 MHz TSEC1: 266 MHz TSEC2: 266 MHz USB MPH: 88 MHz USB DR: 88 MHz CPU: MPC83xx, Rev: 31 at 533.333 MHz Arbiter Configuration Register (ACR): PIPE_DEP: 0x0003 PCI_RPTCNT: 0x0000 RPTCNT: 0x0003 APARK: 0x0000 PARKM: 0x0000 System Priority Configuration Register (SPCR): PCIHPE: 0x0000 PCIPR: 0x0000 TBEN: 0x0001 COREPR: 0x0000 TSEC1DP: 0x0000 TSEC1BDP: 0x0000 TSEC1EP: 0x0003 TSEC2DP: 0x0000 TSEC2BDP: 0x0000 TSEC2EP: 0x0003 Board: Freescale MPC8349ITX I2C: ready DRAM: SDRAM on Local Bus is NOT available! DDR RAM: 256 MB FLASH: 16 MB PCI1 32bit for SATA, PCI2 32bit for PCI slot and miniPCI Data in EEPROM (addr 0x50) is valid. In: serial Out: serial Err: serial Net: Freescale TSEC0: PHY is VSC8201 (fc413) Freescale TSEC0 Board Revision: rev 1.0 IDE: Disable Hit any key to stop autoboot: 3  2  1  0 ## Starting application at 0x00040004 ... VSC7385 Version = 0x273850e9 Value in IRAM matches binary, total bytes 0x2000 loaded ## Application terminated, rc = 0x0 ## Starting application at 0x00040004 ... VSC7385 Version = 0x273850e9 Value in IRAM matches binary, total bytes 0x2000 loaded ## Application terminated, rc = 0x0 ## Booting image at fe810000 ... Image Name: Linux-2.6.13.4 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1548025 Bytes = 1.5 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.6.13.4 (ljd015@ont06-sps-ultra.am.freescale.net) (gcc version 3.4.3) #1 Wed Feb 21 16:29:10 EST 2007 PCI2 confirm: isa_io_base = 0xfc000000 Configure PCI2 controller isa_io_base = 0xfc000000 hose2->io_base_virt = 0xfd000000 Built 1 zonelists Kernel command line: root=/dev/sda1 rw ip=192.168.1.191:192.168.1.117:192.168.1.254:255.255.255.0:PowerQUICC:eth0:off console=ttyS0,115200 IPIC (128 IRQ sources, 8 External IRQs) at fe000700 PID hash table entries: 2048 (order: 11, 32768 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 256256k available (2360k kernel code, 876k data, 120k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Cannot allocate resource region 0 of device 0000:00:00.0 PCI: Cannot allocate resource region 2 of device 0000:00:00.0 PCI: Cannot allocate resource region 0 of device 0001:01:00.0 PCI: Cannot allocate resource region 2 of device 0001:01:00.0 PCI: Failed to allocate mem resource #2:80000000@0 for 0000:00:00.0 PCI: Failed to allocate mem resource #2:80000000@0 for 0001:01:00.0 SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub NTFS driver 2.1.23 [Flags: R/W DEBUG]. Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) eth0: Gianfar Ethernet Controller Version 1.4, 08:00:3e:03:01:10 eth0: MTU = 1500 (frame size=1514,truesize=1780) eth0: Running with NAPI enabled eth0: 64/64 RX/TX BD ring size eth0: Socket buffer recycling mode enabled eth1: Gianfar Ethernet Controller Version 1.4, 08:00:3e:03:01:11 eth1: MTU = 1500 (frame size=1514,truesize=1780) eth1: Running with NAPI enabled eth1: 64/64 RX/TX BD ring size eth1: Socket buffer recycling mode enabled SKB Handler initialized(max=64) sata_sil(0000:00:10.0): cache line size not set. Driver may not function ata1: SATA max UDMA/100 cmd 0xD1000C80 ctl 0xD1000C8A bmdma 0xD1000C00 irq 22 ata2: SATA max UDMA/100 cmd 0xD1000CC0 ctl 0xD1000CCA bmdma 0xD1000C08 irq 22 ata3: SATA max UDMA/100 cmd 0xD1000E80 ctl 0xD1000E8A bmdma 0xD1000E00 irq 22 ata4: SATA max UDMA/100 cmd 0xD1000EC0 ctl 0xD1000ECA bmdma 0xD1000E08 irq 22 ata1: dev 0 ATA, max UDMA/133, 312581808 sectors: lba48 ata1: dev 0 configured for UDMA/100 scsi0 : sata_sil ata2: no device found (phy stat 00000000) scsi1 : sata_sil ata3: no device found (phy stat 00000000) scsi2 : sata_sil ata4: no device found (phy stat 00000000) scsi3 : sata_sil Vendor: ATA Model: Hitachi HDS72161 Rev: P22O Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sda: drive cache: write back SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) SCSI device sda: drive cache: write back sda: sda1 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 usbmon: debugfs is not available driver fsl-usb2-mph, $Revision: 1.1.1.1 $ fsl-usb2-mph fsl-usb2-mph.1: new USB bus registered, assigned bus number 1 fsl-usb2-mph fsl-usb2-mph.1: park 0 fsl-usb2-mph fsl-usb2-mph.1: USB 0.0 initialized, EHCI 1.00, driver $Revision: 1.1.1.1 $ usb usb1: Product: fsl usb20 usb usb1: Manufacturer: Linux 2.6.13.4 fsl-usb2-mph usb usb1: SerialNumber: fsl-usb2-mph.1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27) usbcore: registered new driver rtl8150 usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0 drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5 drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0 usbcore: registered new driver visor drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver v2.1 Freescale PowerPC USB Device Controller driver version 1 August 2005 init g_file_storage gadget: File-backed Storage Gadget, version: 20 October 2004 g_file_storage gadget: Number of LUNs=1 g_file_storage gadget-lun0: unable to open backing file: /root/data/backing_file mpc_udc: fsl-usb2-dr bind to driver g_file_storage i2c /dev entries driver S08QG8: version Version 0.1 - 23 Nov 2006 md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: measuring checksumming speed 8regs : 448.000 MB/sec 8regs_prefetch: 396.000 MB/sec 32regs : 484.000 MB/sec 32regs_prefetch: 528.000 MB/sec raid5: using function: 32regs_prefetch (528.000 MB/sec) md: md driver 0.90.2 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 3.38 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 usb 1-1: new high speed USB device using fsl-usb2-mph and address 2 usb 1-1: Product: USB2.0 Hub hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected eth0: PHY is VSC8201 Gigabit Ethernet (fc413) IP-Config: Complete: device=eth0, addr=192.168.1.191, mask=255.255.255.0, gw=192.168.1.254, host=PowerQUICC, domain=, nis-domain=(none), bootserver=192.168.1.117, rootserver=192.168.1.117, rootpath= md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 120k init Setting the hostname to mpc8349e-mitx Mounting filesystems rootfs / rootfs rw 0 0 /dev/root / ext2 rw 0 0 proc /proc proc rw,nodiratime 0 0 rwfs /mnt/rwfs tmpfs rw 0 0 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Starting syslogd and klogd Setting up networking on loopback device: Setting up networking on eth0: udhcpc (v0.9.9-pre) started Sending discover... Sending discover... Sending discover... No lease, forking to background. Setting up networking on eth1:eth1: PHY is VSC7385 Gigabit Ethernet (7385) Starting inetd: Starting SMB services: /sbin/ip Starting dhcpd Internet Systems Consortium DHCP Server V3.0.3b1 Copyright 2004-2005 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Wrote 0 leases to leases file. Listening on LPF/eth1/08:00:3e:03:01:11/192.168.2/24 Sending on LPF/eth1/08:00:3e:03:01:11/192.168.2/24 Sending on Socket/fallback/fallback-net Done eth1: Full Duplex eth1: Speed 1000BT eth1: Link is up Welcome to Freescale Semiconductor Embedded Linux Environment !!!!! WARNING !!!!!!! The default password for the root account is: root please change this password using the 'passwd' command and then edit this message (/etc/issue) to remove this message mpc8349e-mitx login: